Brickcom VD-series User Manual

Hardware User’s Manual Megapixel Day & Night Vandal Dome Network Camera Quality Service Group Vandal Dome V2 Series

7 3. Below “ Device Appearance Description” is for VD-501Af-series NOTE 1. SD Card Capacity (*) - The network camera is compatibl

8 Chapter 4 - LED Behavior Function LED Behavior Description Power LED Continuous illumination (Green) Power on Power LED Unlit Power off Link LE

9 < Hardware Reset > The Reset Button can be used to reboot the camera or restore it to factory default settings. If the camera experien

10 Chapter 5 - Installation 5.1 Hardware Installation a. Remove the vandal dome cover: Use the Allen Key to unscrew the four screws and remove the

11 c. PoE, Power, DIDO, Audio Connection Put all the cables, such as PoE , 12VDC power , DI / DO / Audio cable , together as one single cable an

12 Terminal Block Pin No. Function Pin No. Function Pin 1 5V Pin 5 Audio OUT Pin 2 D_0 Pin 6 DGND Pin 3 D_I Pin 7 Mic/Line in Pin 4 DIDO GND Pin 8 D

13 ii. Drill four holes as instruted on the sticker. iii. Hammer the four plastic anchors which are provided in the product package into the four

14 WARNING: Do not mount the camera on any soft material. The camera may fall and be damaged.POE, Power, DIDO, Audio Connection: h. Adjust the L

15 get the desired field of view. After completion, tighten the zoom ring controller. ii. Release the focus ring controller bar and slide it left o

16 a. Ethernet and DC12V Connection Connect the camera device to the Ethernet switch using an RJ45 Ethernet cable and connect the DC12V power adapt

Review History: 1. Separate User Manual into HW and SW. 2. Merge VD-100A/ VD-130A/ VD-130N/ VD-300A/ VD-302A/ VD-300N/ VD-302N/ VD-500A / V

17 Operating System: Microsoft Windows XP Home Edition SP2 Microsoft Windows XP Professional SP2 Computer: IBM PC/AT Compatible CPU: Penti

18 5.4 Software Installation In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refe

19 B. In the Install Shield Wizard dialog box, click <Next> to continue. C. Read the End-User License Agreement and check the option “I acc

20 D. Click <Change> to change the appointed folder where installation and program files will be stored. Click <Next> to conti

21 F. Select the application and click <Finish>. When launching the PC-NVR program, please refer to the PC-NVR user manual. 5.4.1 E

22

23 B. Select either “Simple Mode” or “Professional Mode” to obtain the camera’s IP settings. If “Simple Mode” is selected, EasyConfig will

24 C. There may be many cameras in the local network. Differentiate the cameras using their UPnP name. Double click on the camera from the survey l

25

26 F. When the IP address settings have been configured, the screen will either display a successful or failed connection message. If the connectio

Table of ContentsBefore You Use This Product ... 1 Regulatory In

27 c. If the connection was successful, the user will see the message: “Congratulations. The installation of the camera is complete.”

1 Before You Use This Product In many countries, there are laws prohibiting or restricting the use of surveillance devices. This Network

2 Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits

3 Chapter 1 - Package Contents a. Network Camera (Vandal Dome V2 Series) b. Dry Bag, Strap Tie c. Product CD d. Location Sticker e. Warr

4 Chapter 2 - Vandal Dome Network Camera Overview The VANDAL DOME SERIES is a full-featured, 3-axis, fixed-dome, network camera. With a megapixel

5

6 Chapter 3 - Device Appearance Description 1. Below “ Device Appearance Description” is for VD-300Ap 2. Below “ Device Appeara